![]() ![]() Thanks! PC COM PORTS FOR RIG: Enhanced=COM3 Standard=COM4 FT-991A Menu Settings (all default unless otherwise stated below. Haven't found anything online yet, but my Google-fu may be failing me. Be nice if there were a step by step setup somewhere for getting this to work. HELP!!! (see below for setup and screen captures) I'm really hoping I don't need to resort to using the FT-991A's built in voice/CW keyer and the FH-2. I really would like to use the voice keyer in N1MM and still be able to use the mic for voice fills where needed. But when trying to play them via the FT-991A, the rig keys up, but it doesn't actually transmit anything. They play back and sound great via the PC. Here is my dilemma: I have recorded both the S&P and Run voice recordings using N1MM and the PC mic input jack. Of course I use only one digital program at a time. All Rights Reserved.My current setup works great for CAT control, FLDIGI, DM780, and WSJT-X (FT8) using the single connection via the single USB cable. LED Array Kits | Voltage Regulator Kits | View Cart | Support | Contact | About Us | Home Voice Keyer | CW Keyer | Sound Card Interface | Beacon | Band Decoder | Antenna Selector | USB Interfaces Important Information on International Orders ![]() KC-8 CW Cable Set for VK-64 with 1/8" plugĬanada Shipping is $11.00 per order International Shipping is $36.00 per order KC-4 CW Cable Set for VK-64 with 1/4" plug Model KC-8 is terminated with a 1/8" plug. Model KC-4 has the transmitter cable terminated with a 1/4" stereo Paddle cable has connector to the VK-64 on one end and stripped and tinned Includes cables to the paddle and transmitter. Length: 36" - Transmitter section, 30" Microphone section.Email for pricing information on completely assembled and custom length cables. Specify 4 (VKC-4) or 8 (VKC-8) pin microphone connectors. The wires to these connectors come pre-stripped and tinned for quick and painless final assembly to match the pin out requirements for your particular equipment. The VKC-4/8 cables provide the connection between the VK-64 and your rig and microphones. Rear Panel Connectors & Controls Power: Center positive Transmitter and Microphone Audio: DB9 Computer: DB25 CW Paddle: 1/8" Stereo Phono CW Out: RCA Phono Audio Level Adjust: Trim pot adjust Power: 12V DC, 500 ma Audio Messages:4 messages, 15 seconds each CW Output keying: Solid state, for positive keyed rigs only Software compatibility: N1MM Logger, CT, NA, TR-LOG The VK-64-DX comes without a power supply for stations that use a different power connectors or otherwise want to supply their own 12VDC. Adding computer control only needs a standard 25 pin shielded computer cable between theĬables are not included, but can be easily made according to directions in the manual orĪ 12V wall transformer with US standard 2 prong plug is included with the VK-64. Transmitter, even when the VK64 is powered off.ĬW set up is as simple as plugging your paddle into the VK-64. Microphone audio and PTT signals pass through the VK-64 and connect directly to the Plug the microphone into the VK-64's microphone input cable. Installing the VK-64 is easy! Unplug the microphone and plug the VK-64's transmitter audio/PTT cable The VK-64 is compatible with the major contest logging programs, including N1MM Logger, NA, WriteLog, TRLog, CT and LogEQF. The delay time can be adjustedįrom approximately 1/2 to 12 seconds with a front panel control. Message 1 for both CW and voice modes can be set up for auto repeat. Logging programs support sending CW through the printer port.Ĭomputer keying works in parallel with the internal CW keyer. The VK-64 also includes a built in LPT CW interface. A front panel knob adjusts speed from 8-45 WPM. The CW portion is an iambic memory keyer with four programable messages, each one capable of storing over 300 Morse characters. Messages are stored in non-volatile memory, remaining stored until recorded over with a new message. Press the stop button when you are finished. Press the record button followed by a message number button and start talking. ![]() The voice keyer section has four 15 second messages. You can operate the VK64 manually with the front panel controls or under program control through your PC or laptop's printer port. The VK-64 is a voice keyer and CW memory keyer in the same package! This is a legacy product and is no longer available. Unified Microsystems: W9XT VK-64 Combo Voice Keyer/CW Memory Keyer and more for ham radio operators!
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |